Glowing beeswax luminaries. Magical? Heck yeah. Add to that easy, affordable, natural, and DIY and that's my kind of decorating.
It all started with Pinterest. I saw this tutorial for making luminaries with paraffin wax and balloons. And I though: how about beeswax? Beeswax would be warm and sweet and wonderful. So much more alive than paraffin and more "me". Oh, yes. That sounds exceptionally nice.
So with a goal of warm golden globes scattered around our home on New Year's Eve, glowing warmly and scenting the room with the sweetness of summer I dug in. We're having friends over this weekend. Ambiance, anyone? I'm in.
I jotted down a quick tutorial for you, too. If you have some beeswax and balloons you're pretty much set.
DIY Beeswax Luminaries
Beeswax (2 lbs or so with plenty left for other projects...)
Double-boiler, slow cooker, or stainless pot
Fill balloons with warm water. (Or if the only faucet in your house that will take a balloon is cold water only, fill a basin with warmish-hot water and soak your cold balloon's for a while.) Fill them to the size that you want your luminary to be.
Your balloons should be full enough that they are plump/taught. If you want smaller luminaries, simply knot them off as tightly as possible like the balloon above (note the long "tail"). I say this because I had trouble with under-filled balloon's. The luminary cracked when I set them down to cool, an issue I did not have with full or tied-with-a-long-tail balloons.
Heat your beeswax. Ideally you want it around 160-170F. I do this in a slow cooker that I picked up at a thrift store just for this job. If you don't have a slow cooker you can simply use a cooking pot on low heat or fashion a double boiler out of two pots. (Be prepared to donate the wax pot to wax forever more. Though it is possible - and a bit of a headache - to clean out.)
Melt the wax on high, then turn it to low before you set to work. I only checked the temp twice during a 40 minutes of luminary making and it held temp well. No thermometer? No worries.
If you don't have a thermometer, wing it. Here's how you know you have the right temp:
- Is the wax sticking smoothly to your balloon? Then it's your temp is good! Dip.
- Is the wax lumpy? Too cool! Heat it up.
- Is the wax melting the previous layer off when you re-dip? Too hot! Allow to cool.
Dip your balloon repeatedly. Do not dip beyond the water/air line on your balloon. If you wonder why and decide to try it your balloon will dramatically explode, filling your wax pot with water and causing you much grief. (Ask me how I know...)
Every six dips or so gently place the balloon on a piece of parchment paper to flatten the bottom. Let it sit for a bit to cool. Between every dip allow 5-10 seconds for the wax to cool before you immerse it in the wax another time. (I like to do two balloons at a time, alternating between them.)
Random sidebar to answer the question you are asking: that's my dry erase board in the background above. The tutorial for making that is over here.)
After approximately 20-30 dips, gently place your balloon on the parchment and allow to cool. Your goal is a luminary that is thick enough to hold up to use, yet thin enough to let the light through. Once it feels firm to the touch (though still warm) take your balloon to the sink and pop it! It will startle you every time. I promise. And you will likely get a little wet if your aim is off. Peel away and discard the balloon.
Trim any ragged edges with a pair of sharp scissors while the luminary is still warm. Then place a tea light or votive (in a cup) inside and enjoy. (The brighter your candle the warmer the glow.)
Happy New Year to you. I'll be back her next week with more treats in store.